What is a VOR? What frequency range and band is it in?

What is a VOR? What frequency range and band is it in?

VHF Omnidirectional Radio Range (VOR) is defined as VHF Omnidirectional Radio Range, an aircraft navigation system operating in the VHF band.

VOR's are assigned radio channels between 108.0 MHz and 117.95 MHz (with 50 kHz spacing); this is in the very high frequency (VHF) range.

How does GPWS work?

How does GPWS work?

GPWS is a central computer system that receives various data inputs on configuration, (radio altimeter) height/altitude and instrument landing system glide slope deviation and is able to alert the pilot when a dangerous situation is about to occur.

What are TORA, TODA, ASDA clearways, stopways, and screen heights?

What are TORA, TODA, ASDA clearways, stopways, and screen heights?

TORA= Takeoff Run Available, the length of runway declared available and suitable for the ground run of an aeroplane taking off.

TODA= Takeoff Distance Available, the length of the take off run available (TORA) plus the length of the clearway, if available.

ASDA= Accelerated Stop Distance Available, the length of the takeoff run plus the length of the stopway, if available.

A clearway is an area beyond the paved runway, free of obstructions and under the control of the airport authorities. The length of the clearway may be included in the length of the takeoff distance available (Take Off Distance Available (TODA)). For example, if a paved runway is 2000 m long and there are 400 m of clearway beyond the end of the runway, the takeoff distance available is 2400 m long.

The stopway is an area beyond the runway which can be used for deceleration in the event of a rejected takeoff.

Screen height: TODR is the distance from the brake release point to the point where the aircraft gains a height of 35 ft above the ground. This 35 ft is what we call the screen height. While 35 ft is the screen height for class A airplanes, it is 50 ft for class B airplanes.

On a wet runway, the screen height is reduced to 15 ft.

Can VMCG be lower than V1? Explain.

Can VMCG be lower than V1? Explain.

Yes, VMCG has to be equal to or less than V1 to ensure the aircraft could maintain runway heading having suffered an engine failure at or above V1 when the aircraft is committed to takeoff.

Why is anhedral used instead on some aircraft?

Why is anhedral used instead on some aircraft?

Anhedral:

compensates for the wing sweep improves roll maneuverability

What are the advantages of fuel injection vs a carburetor?

What are the advantages of fuel injection vs a carburetor?

Fuel injection provides:

  • Fuel free from vaporization ice

  • Better economy through metered delivery

  • More responsive and efficient engine

  • Less maintenance

If turboprops are more efficient aircraft, why do they not climb that high?

If turboprops are more efficient aircraft, why do they not climb that high?

Jet engines are designed to achieve their best specific fuel consumption at high rpm, which can only be achieved at high altitudes where the air density is low.

Thrust produced will be low enough to equal the required cruising thrust. Also high altitude gives the best operating conditions for the airframe i.e. minimum drag during the cruise.

Turboprops need relatively dense air for the propellers to work efficiently and at high altitude the density would be too low.

What is ACA/H? What ACA/H did you use? Why do we have an ACA/H?

What is ACA/H? What ACA/H did you use? Why do we have an ACA/H?

Asymmetric Committal Altitude/Height is the minimum height needed to establish a positive climb whilst maintaining adequate speed for control and removal of drag during an approach to a landing.

In the Seneca at Oxford we used 200ft AGL. At this altitude when continuing for landing you selected the landing flaps (check clear runway, on speed, on altitude, landing clearance received).

You now are committed to land, single engine G/A with flaps 40 and gear down is not possible in a Seneca.

Tell me about the last aircraft you flew in.

Tell me about the last aircraft you flew in.

Example answer for a candidate with previous Seneca experience:

Weights:

Max all up weight – take off 4570lbs Max all up weight – landing 4340lbs Empty weight - 2830lbs Usefull load - 1740lbs

Speeds:

Clean stall 66kts with flaps 60kts Vyse 89kts Cruise 140kts gear raising 107kts – lowering 129kts. Vne 195

The 6 cyclinder teledyne continental turbo- charged, fuel injected engines provide 200 hp at 2575.

Left engine rotated clockwise and right anti clockwise.

No critical engine, RayGay turbo’s 42” MAP, 40” limit at lower levels, cowl flaps provide cooling and has 3 positions, open mid and closed.

Avgas 100/130

Props 2 or 3 blade, constant speed, hydraulically actuated, fully feathering.

Oil keeps props at fine pitch, gas and air keep the rpm towards feather. Takes 6 seconds to feather and must happen before locks engage at 800 rpm.

Limit load factor 3.8G

Fuel 2 x 54 (64US) gallons tanks 8 quarts oil max 6 Min

Retractable gear – hydraulic pumps – electrically driven. 6-7 seconds transit

Nose gear has 27 degrees castor.

Main wheels 55psi, nose wheel 31psi

Cable operated controls, all moving stabilator with anti servo tab which acts as a trim.

Frise ailerons and differential ailerons, up more than down.

Manual flaps, 3 settings, 10, 25, 40 degrees.

4.5” – 5.2” hg suction – AH, DI.

Heated lift deflectors and stall warners, anti ice.

Tell us what ranges the glideslope and localiser beams are checked out to?

Tell us what ranges the glideslope and localiser beams are checked out to?

Glideslope: 329.15-335Mhz UHF 8 degrees either side, 10NM

Localiser: 108.10-111.95Mhz VHF 35 degrees either side, 17NM

You have reached the end of the test!Share LinkFinish