• The packs produce the coolest temperature selected in any of the zones, with the other zones temperature controlled by adding hot trim air to produce the required temperature.

    ✅ True

  • Where are the wing-body overheat sensors located?

    • ❌ Engine struts, wing leading edge slats, air conditioning bays, APU duct, keel beam.
    • ✅ Engine struts, wing inboard leading edges, air conditioning bays, APU bleed duct, keel beam.
    • ❌ Engine cowling lips, wing leading edge slats, air conditioning bays, APU compartment, keel beam.
    • ❌ Engine cowl lips, wing leading edge slats, air conditioning bays, electronic equipment bay, APU bleed duct.
  • Engine bleed air pressure is controlled by means of the bleed air valve which acts as both a shutoff and pressure regulating valve.

    ✅ True

  • What is the primary function of the recirculation fans?

    • ❌ To provide standby air conditioning if the packs fail.
    • ✅ Reduce engine bleed air demand and load on the packs.
    • ❌ Recirculate cabin air to allow it to be filtered to remove contaminants as it passes through the recirculation fan HEPA filters.
    • ❌ Recirculate the air from the passenger cabin to provide heating for the forward cargo compartment
  • Which statement is correct:

    • ❌ Bleed air is constantly provided from stage 5 and stage 9 of the compressor.
    • ✅ Bleed air is only supplied from the 9th stage when the valve modulates open if bleed air requirement is greater than the 5th stage alone can supply.
    • ❌ Bleed air is only supplied from the 5th stage when the valve modulates open if bleed air requirement is greater than the 9th stage alone can supply.
    • ❌ ----
  • What is the function of the dual Bleed Light?

    • ❌ Illuminates to warn of possible backpressure whenever both engines are providing bleed air, and engines are at different thrust settings.
    • ❌ Illuminates whenever both APU and engines is running to warn of risk of backpressure to APU.
    • ✅ Illuminates when engine running and APU bleed air valve, engine bleed air valve, and isolation valve are in a position to permit possible backpressure of the APU.
    • ❌ Illuminates whenever pressure in APU rises above a pre-set value.
  • If all zone and primary pack controls fail, how is cabin temperatures controlled?

    • ❌ The last settings before the failure will be maintained until the packs are selected OFF.
    • ❌ The cabin temperatures cannot be controlled in this situation.
    • ✅ The standby pack controls command the packs to produce the average temperature demand of the 2 passenger cabin zones.
    • ❌ A fixed cabin temperature will be produced in this situation - 24 degrees C from the left pack, and 18 degrees C from the right pack.
  • The differential pressure of the cabin is limited by a pressure relief system - which of the following statements is correct?

    • ❌ There is a negative pressure relief valve, which limits the cabin pressure to 9.1 psi above ambient.
    • ❌ There is an outflow valve which opens when cabin pressure reaches 9.1 psi above ambient.
    • ❌ There are two negative pressure relief valves, which limit the cabin pressure to 9.1 psi above ambient.
    • ✅ There are two pressure relief valves which limit differential pressure to 9.1 psi.
  • Which systems use engine bleed air during operation?

    • ✅ Engine starting, air conditioning, cabin pressurisation, engine and wing anti-icing, hydraulic, water.
    • ❌ Engine and wing anti-icing, engine starting, cabin pressurisation, hydraulic reservoir pressurisation.
    • ❌ Engine and wing anti-icing, air conditioning, cabin pressurisation, hydraulic reservoir pressurisation.
    • ❌ Engine and wing anti-icing, engine starting, air conditioning, cabin pressurisation, hydraulic reservoir pressurisation.
  • Cabin pressurisation is controlled by the position of the Outflow Valve, but some air is also exhausted through the toilet and galley vents.

    ✅ True

  • Bleed air is taken from stage 5 from the low pressure compressor and stage 9 of the high pressure compressor.

    ✅ True

  • What is the result if all temperature zone selectors are positioned to OFF?

    • ❌ The right pack will produce a fixed temperature of 75 degrees Fahrenheit, and the left pack will produce a fixed temperature of 65 degrees Fahrenheit.
    • ✅ Left pack will produce 24 degrees centigrade and right pack will produce 18 degrees centigrade.
    • ❌ The packs will attempt to maintain an average temperature across all zones.
    • ❌ ----
  • The APU is capable of supplying bleed air for two packs on the ground, or one pack in flight.

    ✅ True

  • When operating on the Standby Pack Controls, what temperatures will the packs be producing?

    • ✅ An average temperature for the two cabin zones.
    • ❌ The trim air modulating valves close so no pack air is provided to the two cabin zones, only re-circulated air is provided.
    • ❌ Left pack produces 18 degrees C, right pack produces 22 degrees C.
    • ❌ The flight deck required temperature will also be provided to the passenger cabin.
  • The TRIP RESET switch is pushed to reset a PACK, WING-BODY OVERHEAT and BLEED TRIP OFF, it isolates the associated valve and extinguishes the alert.

    ❌ False

  • How many Trim Air Pressure Regulators are there in the Air Conditioning system?

    • ❌ 2
    • ❌ 3
    • ✅ 1
    • ❌ There are no Trim Air Pressure Regulators, only Trim Air Modulating valves.
  • Bleed air is taken from stage 4 and stage 10 of the high pressure compressor.

    ❌ False

  • Conditioned air from the left hand pack flows directly to the Flight Deck from the Mix Manifold.

    ❌ False

  • Bleed air is taken from stage 5 and stage 9 of the high pressure compressor.

    ❌ False

  • What is the result if one pack fails in-flight?

    • ❌ The remaining pack when selected to AUTO will be capable of maintaining pressurisation up to aircraft ceiling, only if all Zone Temperature Controllers are selected to OFF.
    • ❌ The remaining pack will not operate in HIGH flow.
    • ✅ The remaining pack is capable of maintaining pressurisation and acceptable cabin temperatures up to 41,000 feet.
    • ❌ The remaining pack will be capable of maintaining pressurisation up to the aircraft maximum certified ceiling, and will attempt to produce an average temperature across all cabin zones.
  • If all Temperature Selectors are positioned OFF, the pack controls will cause the packs to produce which fixed temperatures?

    • ✅ Left Pack, 24 degrees Centigrade. Right Pack, 18 degrees Centigrade.
    • ❌ Left Pack, 20 degrees Centigrade. Right Pack, 22 degrees Centigrade.
    • ❌ Left Pack, 18 degrees Centigrade. Right Pack, 24 degrees Centigrade.
    • ❌ Left Pack, 22 degrees Centigrade. Right Pack, 20 degrees Centigrade.