• SMOKE CONFIGURATION. By pushing both the BLOWER and EXTRACT pb to override, the following happens to the ventilation System:

    • ❌ Both fans stop and the air is extracted overboard
    • ✅ The blower fan stops and the air is extracted overboard
    • ❌ The extract fan stops and the air is extracted overboard
    • ❌ The Inlet & Outlet flap opens, blower fan stops and the air is extracted overboard
  • With both the BLOWER and EXTRACT pushbutton switches in AUTO, what ventilation configurations do you normally expect to see?

    • ❌ Closed configuration on the ground before applying TO power and open configuration after applying TO power and in the air
    • ❌ Intermediate Configuration on the ground and open configuration in the air
    • ❌ Open configuration on the ground and smoke configuration in the air
    • ✅ Open configuration on the ground before applying TO power and closed configuration after applying T/O power and in the air
  • When the BLOWER pb is on OVRD:

    • ❌ The system goes to open circuit configuration
    • ✅ The system goes to closed circuit configuration
    • ❌ The blower fan will continue to run
    • ❌ The blower fan is de-energized for the remainder of the flight
  • What is the maximum negative differential pressure for the cabin:

    • ❌ 0 PSI
    • ✅ - 1 PSI
    • ❌ - 2 PSI
    • ❌ + 1 PSI
  • The two cabin pressure controllers receive signals from:

    • ❌ ADIRS only
    • ❌ ADIRS and FMGC only
    • ✅ ADIRS, FMGC, LGCIU and EIU
    • ❌ ADIRS, FMGC and EIU only
  • On ECAM CAB PRESS page, the outflow valve indicator changes to amber when the valve

    • ❌ is fully closed
    • ✅ open more than 95% during flight
    • ❌ is fully closed
    • ❌ is in transit
  • Under what conditions should the pack flow controller on an A319 be set to HI?

    • ❌ In cold conditions to achieve a higher cabin temperature range
    • ❌ If the number of Passengers is below 115
    • ✅ For abnormal hot and humid conditions
    • ❌ If the number of occupants is above 138
  • In AUTO, the cabin differential pressure is normally controlled by…

    • ❌ The SAFETY valve
    • ❌ The INLET valve
    • ❌ The EXTRACT valve
    • ✅ The OUTFLOW valve
  • The temperature of the cockpit can be regulated from:

    • ✅ The Cockpit
    • ❌ The Cabin
    • ❌ All Answers are correct
    • ❌ The temperature of the cabin is regulated via the CPC
  • APU bleed supply on ground. With the pack flow selector on set to NORM, what is the actual pack flow?

    • ❌ LO with 80% pack valve flow
    • ❌ NORM with 100% pack valve flow
    • ❌ HI with 150 % pack valve flow
    • ✅ HI with 120% pack valve flow
  • The PACK FLOW controller is set to NORM and yet the ECAM display shows PACK FLOW to be high. How is this possible?

    • ❌ As the engines are not running the PACK FLOW indicators are at the position they were selected to at the last shut down
    • ❌ As no bleed air is available the PACK FLOW valves are spring loaded to the fully open position
    • ✅ HI flow is automatically selected regardless of PACK FLOW selector position because air is only being supplied by the APU
    • ❌ With cold outside air conditions the PACK FLOW is automatically increased to help increase the cabin temperature
  • In case of failure of one cabin pressure controller:

    • ❌ The transfer to the second controller is automatic but the cabin v/s must be controlled manually
    • ✅ The transfer is automatic and the second controller (which was in standby) takes over
    • ❌ The transfer to the second controller must be executet manually by resetting the CABIN PRES MODE SEL pb for at least 10sThe transfer to the second controller must be executed manually by resetting the CABIN PRES MODE SEL pb for at least 10s
    • ❌ The transfer to the second controller is not possible inflight. They will only be switched automatically 70s after landing
  • What would cause an amber PACK FAULT light on the PACK pb-sw to illuminate?

    • ❌ Pack outlet overheat
    • ❌ Compressor outlet overheat
    • ❌ Switch position disagreement in comparison to the pack flow control valve
    • ✅ All answers are correct
  • The safety valves are …

    • ❌ Controlled with the MAN V/S CTL
    • ❌ Controlled with the MODE SEL pb
    • ❌ Controlled with the DITCHING pb
    • ✅ Cannot be controlled manually (independent)
  • What is the limiting factor for opening the RAM AIR valve?

    • ❌ Aircraft at or below 10’000ft
    • ✅ Cabin differential pressure below 1 PSI
    • ❌ Aircraft must be on ground
    • ❌ Aircraft must be fully depressurized
  • When can we have a closed circuit configuration in normal operation?

    • ❌ The aircraft must be on the ground with the thrust levers not at TO and the skin temp above a given threshold
    • ❌ The aircraft must be on the ground with the thrust levers at TO and the skin temp above a given threshold
    • ❌ The aircraft must be on the ground with both engines stopped and the skin temperature below a given threshold
    • ✅ The aircraft must be in the air, or on the ground with the thrust levers at TO and the skin temp below a given threshold
  • The zone controller or the air conditioning system controllers (ACSC) optimize temperature by acting on the?

    • ✅ Trim air valves
    • ❌ Skin air valves
    • ❌ Isolation valves
    • ❌ Pack valves
  • The temperature of each aircraft zone is optimized by means of …?

    • ❌ A hot air valve
    • ❌ A zone control valve
    • ❌ A pack valve
    • ✅ A trim air valve
  • The cabin pressurization system consists, among others, of:

    • ❌ One outflow valve, one cabin pressure controller and two safety valves
    • ❌ One outflow valve, two cabin pressure controllers and one safety valve
    • ✅ One outflow valve, two cabin pressure controllers and two safety valves
    • ❌ Two outflow valves, one cabin pressure controller and two safety valves
  • The RAM AIR INLET is powered via…

    • ❌ AC BUS 1
    • ❌ AC BUS 2
    • ✅ DC ESS BUS
    • ❌ DC BUS 1
  • The avionics ventilation system is fully automatic. The normal operation configurations are:

    • ❌ Open-circuit configuration, close-circuit configuration, smoke configuration
    • ❌ Open-circuit configuration, close-circuit configuration
    • ✅ Open-circuit configuration, intermediate configuration, close-circuit configuration
    • ❌ Open-circuit configuration, partially-open configuration, bypass-circuit configuration
  • Which statement is correct? Two independent pneumatic safety valves prevent cabin pressure from going…

    • ❌ Too high (8.6 psi above ambient)
    • ❌ Too low (1 psi below ambient)
    • ✅ Too high (8,6 psi above ambient) or too low (1 psi below ambient)
    • ❌ Too high (9 psi above ambient) or too low (1 psi below ambient)
  • Emergency evacuation checklist. Why do you have to check Δp = 0 if MAN CAB PR has been used?

    • ✅ Because the outflow valve does not open automatically at touchdown
    • ❌ To facilitate the opening of the cargo doors by fire brigadee
    • ❌ Because the safety valves are closed
    • ❌ Because of a possible non indicated failure of the Residual Pressure Control Unit (RPCU)
  • The input of the QNH in the FMGS for the approach influences, among others….

    • ❌ The GS mini
    • ✅ The pressurization schedule of the CPC Cabin Pressure Controllers
    • ❌ The pressurization schedule and the GS mini
    • ❌ The BARO minimum for NON-PROC. Appr
  • The MODE SEL pb sw in MAN mode allows you to use the MAN V/S CTL in order to…

    • ❌ Manually alter the air inlet valve setting
    • ❌ Manually adjust the pack flow valve
    • ✅ Manually adjust the outflow valve
    • ❌ Manually alter the pack outflow valve setting
  • When the cooling demand in one zone cannot be satisfied, if the bleed pressure is too low, the zone controller sends a pressure demand signal to both Engine Interface Units (EIU) to

    • ❌ Decrease the minimum idle and to raise the bleed pressure
    • ✅ Increase the minimum idle and to raise the bleed pressure
    • ❌ The zone controllers cannot send signals to the EIU to alter any engine parameter
    • ❌ All answers are correct
  • Which answer about the two zone controllers or ACSC (Air Conditioning System Controller) of the air conditioning system is correct?

    • ✅ Controller 1 regulates the cockpit temperature, controller 2 the temperature in the two cabin zones
    • ❌ Controller 1 regulates the temperature in the two cabin zones, controller 2 the cockpit temperature
    • ❌ Controller 1 regulates the cockpit temperature, controller 2 the temperature in the three cabin zones
    • ❌ Controller 1 regulates the temperature in the three cabin zones, controller 2 the cockpit temperature
  • The PACK FLOW selector on an A320 is in LO position. Which statement is correct?

    • ❌ The pack valve flow selection is 80%
    • ❌ The pack flow can be automatically selected up to 100% when the cooling demand cannot be satisfied
    • ❌ With APU bleed supply or single Pack operation, HI pack valve flow is automatically selected
    • ✅ All answers are correct
  • The cabin pressure during lift-off and at touchdown is ________ ambient pressure

    • ✅ Higher than
    • ❌ Lower than
    • ❌ Equal to
    • ❌ Irrespective of
  • Having manually set the LDG ELEV the cabin altitude is…

    • ❌ Only controllable manually through the MAN V/S CTL
    • ✅ Still controlled automatically through the outflow valve
    • ❌ Still controlled normally through the safety valve
    • ❌ Only controllable manually through the LDG ELEV selector
  • The pack flow control valve closes automatically in case of:

    • ✅ Pack overheat, engine fire push button operation, engine start, ditching push button pressed
    • ❌ Bleed valve failure, pack outlet pressure increase
    • ❌ All Answers are correct
    • ❌ Takeoff when takeoff power is set and the main landing gear struts are compressed
  • With both the BLOWER and EXTRACT pushbutton switches in OVRD, what happens to the ventilation system?

    • ❌ The system goes into open configuration and the blower fan stops
    • ✅ The system goes into smoke configuration and the blower fan stops
    • ❌ The system goes into open configuration and the extract fan stops
    • ❌ The system goes into intermediate configuration and the extract fan stops
  • When do you switch the pack flow selector on an A320 to HI?

    • ❌ If number of PAX is ≥ 115
    • ❌ Never
    • ✅ For abnormally hot and humid conditions
    • ❌ If the number of Passengers is more or equal to 150
  • The hot air pressure regulating valve closes automatically, if:

    • ❌ The duct overheats
    • ❌ The cockpit trim air valve fails
    • ❌ Both cabin trim air valves fail
    • ✅ All answers are correct
  • Regarding Avionics Ventilation: When can we have an open circuit configuration in normal operation?

    • ✅ The aircraft must be on the ground with the thrust levers not at TO and the skin temperature above the on ground threshold
    • ❌ The aircraft must be on the ground with the thrust levers at TO and the skin temperature above the on-ground threshold
    • ❌ The aircraft must be in the air with the thrust levers not at TO and the skin temperature below a given threshold
    • ❌ The aircraft must be in the air or on-ground with thrust levers at TO an the skin temperature above a given inflight threshold
  • The FAULT light on the PACK 1 or 2 pb switch comes on amber:

    • ❌ If the pack flow control valve position disagrees with the selected position
    • ❌ In the case of compressor outlet overheat
    • ❌ In the case of pack outlet overheat
    • ✅ All answers are correct
  • With bleed air supplied from the APU (APU bleed valve open or same pack operation) the pack flow is automatically selected to:

    • ✅ High
    • ❌ Normal
    • ❌ Low
    • ❌ ECON
  • On ECAM CAB PRESS page the cabin altitude indication changes to red when cabin altitude

    • ❌ Goes above 14.000 ft
    • ❌ Goes above 8.500 ft
    • ✅ Goes above 9.550 ft
    • ❌ Goes above 12.000 ft
  • When does the pack flow control valve close?

    • ❌ In case of pack overheating
    • ❌ During engine start
    • ❌ When operating fire or ditching P/B
    • ✅ All answers are correct
  • The ram air inlet flap of the air conditioning pack:

    • ❌ Closes during takeoff when takeoff power is set and the main landing gear struts are compressed
    • ❌ Opens during landing and closes as soon as the main landing gear struts are compressed, as long as speed is at or above 70 knots
    • ❌ It opens 20 seconds after the speed drops below 70 knot
    • ✅ All answers are correct