• What do you have to consider if you have to disconnect an IDG?

    • ❌ Push the IDG pb-sw for at least 3 seconds
    • ✅ Disconnect the IDG only when the engine is running or windmilling
    • ❌ Push the IDG pb-sw for at least 4 seconds
    • ❌ Nothing needs to be considered
  • A Generator Control Unit (GCU) controls the output of each generator. The main function(s) of each GCU are:

    • ✅ Control the frequency and voltage of the generator output and protect the network by controlling the associated Generator Line Contactor (GLC)
    • ❌ Control the voltage of the generator output only
    • ❌ Control the frequency of the generator output only
    • ❌ Controls the revolutions of each generator drive gear in order to get constant Frequency
  • The generator indications on the ECAM page are:

    • ✅ Load (%), voltage (V) and frequency (HZ)
    • ❌ Load (A), voltage (V) and frequency (HZ)
    • ❌ Load (A) and frequency (HZ) only
    • ❌ Voltage (V) and frequency (HZ) only
  • How is the emergency generator powered?

    • ✅ The ram air turbine (RAT) must be extended. This powers the blue hydraulic system, which drives the emergency generator by means of a hydraulic motor
    • ❌ The ram air turbine (RAT) must be extended. This powers the green hydraulic system, which drives the emergency generator by means of a hydraulic motor
    • ❌ By the yellow hydraulic power through the PTU to drive EMER ELEC GEN in the green hydraulic system
    • ❌ By one of the electric pumps, whichever is switched on
  • If the RAT stalls, or if the aircraft is on the ground with a speed below 100kt, the emergency generation network transfers automatically to the batteries and the static inverter, and the system automatically sheds the:

    • ❌ AC SHED ESS BUS only
    • ❌ DC SHED ESS BUS only
    • ✅ AC SHED ESS BUS and DC SHED ESS BUS
    • ❌ AC ESS BUS only
  • What are the priorities in the electrical power supply of the A/C?

    • ✅ GEN 1 and 2 over APU and over EXT PWR. External power has priority over APU generator when the EXT PWR pb switch is ON
    • ❌ APU over EXT PWR over GEN 1 and 2
    • ❌ EXT PWR over GEN 1 and 2 over APU
    • ❌ APU over GEN 1 and 2 over EXT PWR
  • Which statement concerning COMPUTER RESET / CB policy is correct?

    • ❌ Do not pull the SFCC & LGCIU CBs
    • ❌ Do not pull the ECU & SEC CBs
    • ❌ Do not pull the EIU & FAC CBs
    • ✅ Do not pull the SFCC & ECU or EEC, EIU CBs
  • The RAT extends automatically if

    • ❌ AC BUS 1 fails
    • ✅ AC BUS 1 and AC BUS 2 fail
    • ❌ DC BUS 1 and DC BUS 2 fail
    • ❌ AC BUS2 and DC BUS 1 fails
  • While operating in emergency electrical configuration with the landing gear extended, which of the following control laws is active?

    • ✅ Direct law
    • ❌ Alternate law
    • ❌ Backup law
    • ❌ Mechanical law
  • If the GEN 1 LINE pb-sw is switched to OFF:

    • ❌ AC BUS 1 disconnects and GEN 1 is switched OFF
    • ✅ AC BUS 1 channel is supplied from GEN2 through bus tie contactors. The inner tank pumps 1 are supplied directly by IDG and pump relays by DC ESS
    • ❌ AC BUS 2 disconnects, GEN 1 is still working and supplies AC BUS 1
    • ❌ AC BUS 1 disconnects, GEN 1 is still working and supplies AC BUS 2
  • AC power can be generated by:

    • ❌ The 3 generators only
    • ❌ The 3 generators or an emergency generator
    • ✅ The 3 generators or an emergency generator or a static inverter supplied by batteries
    • ❌ By the two engine driven generators only
  • What happens when the GEN 1 pushbutton switch is set to the OFF position?

    • ✅ The generator field is de-energized and line contactor opens. The fault circuit is reset
    • ❌ The generator is still energized and line contactor open
    • ❌ The generator field is de-energized and line contactor remains closed
    • ❌ The generator field is energized and the line contactor closes if electrical parameters are normal
  • Which failure combination will trigger the EMER ELEC configuration automatically?

    • ❌ DC BUS 1 is not electrically supplied and DC BUS 2 is not electrically supplied and Aircraft speed is greater than 100 kt
    • ❌ AC BUS 1 is not electrically supplied and DC BUS 2 is not electrically supplied and Aircraft speed is greater than 100 kt or vice versa (AC BUS 2 and DC BUS 1)
    • ✅ AC BUS 1 is not electrically supplied and AC BUS 2 is not electrically supplied and Aircraft speed is greater than 100 kt
    • ❌ AC ESS BUS is not electrically supplied and DC ESS BUS is not electrically supplied and Aircraft speed is greater than 100 kt
  • The BAT FAULT light illuminates if:

    • ❌ The battery voltage is less than 25V
    • ❌ The battery pb-sw is set to off in flight
    • ✅ The charging current for the corresponding battery is outside limits
    • ❌ All answers are correct
  • The EMERGENCY GENERATOR supplies :

    • ❌ DC BUS 1 and DC BUS 2
    • ❌ AC BUS 1
    • ❌ AC BUS 2
    • ✅ AC ESS BUS
  • The aircraft has two types of C/Bs:

    • ✅ Monitored (green), non-monitored (black)
    • ❌ Monitored (green), non-monitored (red)
    • ❌ Monitored (black), non-monitored (green)
    • ❌ Monitored (red), non-monitored (green)
  • IDG FAULT light lights up amber if:

    • ✅ The IDG oil outlet overheats or IDG oil pressure is low
    • ❌ The IDG is disconnected
    • ❌ The IDG outlet oil TEMP too low or IDG oil outlet overheats
    • ❌ The IDG is disconnected and IDG oil pressure is low
  • TRIPPED C/B RE-ENGAGEMENT A FUEL PUMP C/B has tripped by itself. Which statement regarding the re-engagement is correct

    • ❌ On ground do not reengage the C/B of the fuel pump(s) of any tank
    • ❌ In flight do not reengage the C/B of the fuel pump(s) of any tank
    • ✅ both answers are correct
    • ❌ ---
  • The RAT extends automatically when:

    • ❌ The MAN ON pb on the EMER ELEC PWR panel has been pressed and both DC BUS 1 and 2 have failed
    • ❌ The MAN ON pb on the EMER ELEC PWR panel is guarded and AC BUS 1 is not electrically supplied
    • ❌ The MAN ON pb on the EMER ELEC PWR panel is guarded, the aircraft speed is above 72 kt and AC BUS 2 is not electrically supplied
    • ✅ The MAN ON pb on the EMER ELEC PWR panel is on AUTO, AC BUS 1 and 2 are not electrically supplied and the aircraft speed is greater than 100 kt
  • Which bus is not powered during EMER ELEC in flight?

    • ❌ AC ESS BUS
    • ❌ DC ESS SHED BUS
    • ✅ DC BAT BUS
    • ❌ both AC ESS BUS & DC ESS SHED BUS
  • What does the BAT check of the PNF include during Preliminary Cockpit Preparation?

    • ❌ BAT 1+2 OFF, then ON, check currents drop below 60A within 10sec
    • ❌ BAT 1+2 ON, check voltage > 25.5 V
    • ✅ Check BAT 1+2 OFF, check voltage > 25.5 V
    • ❌ BAT 1+2 OFF, then ON, check voltage > 25.5 V
  • The two batteries are connected to the DC BAT BUS if they need charging. When they are fully charged the battery charge limiter:

    • ✅ Disconnects them
    • ❌ Maintains a trickle charge
    • ❌ Remains connected
    • ❌ Disconnects them, but after a time delay of exactly 20min they will be connected again
  • Which statement about the IDG is correct?

    • ✅ Pushing the IDG pb-sw for more than 3 seconds may damage the IDG disconnection mechanism
    • ❌ Push the IDG pb for at least 3 seconds to disconnect the IDG
    • ❌ The IDG can be reconnected at anytime
    • ❌ The FAULT light on the IDG pb remains ON after disconnection of the IDG
  • On ground with external power connected and MAINT BUS switch ON, the AC and DC GND/FLT buses are supplied by:

    • ✅ External power directly
    • ❌ APU or external power via AC BUS 2
    • ❌ External power via AC BUS 1
    • ❌ External power via AC BUS 2
  • If AC BUS 1 fails, the AC ESS BUS is supplied by:

    • ❌ Emergency generator
    • ✅ AC BUS 2
    • ❌ Battery 2 via the static inverter 2
    • ❌ ---
  • If the IDG is disconnected once.

    • ❌ The IDG may be reconnected in flight
    • ✅ The IDG may be reconnected on ground only
    • ❌ The IDG may be reconnected in flight in idle thrust only
    • ❌ The IDG must be exchanged by maintenance
  • On the emergency electric power panel, a fault light illuminates under the 'RAT and EMER GEN' label. What does it mean?

    • ❌ RAT is not extended
    • ❌ The emergency generator is not supplying when AC bus 1 and 2 are not powered (above 100 kts) or DC bat bus is not powered
    • ❌ The emergency generator is supplying but AC ess bus is not powered
    • ✅ The emergency generator is not supplying power when AC bus 1 and 2 are not powered
  • What would happen to the battery voltage if you switch off the main power supply (EXT PWR+APU) and leave the BAT 1 and BAT 2 pushbuttons in the AUTO position?

    • ❌ The batteries would discharge completely
    • ✅ The automatic cut-off logic would prevent the batteries from discharging completely
    • ❌ Nothing, because the batteries are not connected to the DC BAT BUS
    • ❌ Only battery 2 would discharge completely
  • What is the important thing to remember, to avoid damaging the disconnection mechanism of the IDG, when the IDG pb-sw will be pushed?

    • ❌ To push the IDG pb-sw until the GEN FAULT light comes on and then for at least 3 more seconds
    • ✅ To push the IDG pb-sw for a maximum of 3 seconds but make sure that the engine is running or windmilling
    • ❌ To push the IDG pb-sw for at least 10 seconds to ensure the disconnection
    • ❌ To push the IDG pb-sw until the GEN FAULT light comes on, but only for a maximum of 5 seconds
  • The time for the ECAM to trigger the C/B TRIPPED warning for Monitored C/Bs is:

    • ✅ 1 min
    • ❌ 2 min
    • ❌ 3 min
    • ❌ 4 min
  • How much is the power output of each engine driven generator?

    • ✅ 90 KVA
    • ❌ 45 KVA
    • ❌ 5 KVA
    • ❌ ---
  • When the aircraft main electrical system is not powered, the battery voltage can be checked:

    • ❌ On the ECAM electrical system page
    • ✅ On the electrical section of the overhead panel
    • ❌ There are no indications
    • ❌ Both on the ECAM electrical system page and on the electrical section of the overhead panel
  • Which statement concerning the electrical generators is correct?

    • ❌ One engine generator can supply the entire network
    • ❌ The generators cannot be connected in parallel
    • ✅ All answers are correct
    • ❌ The APU generator or external power can supply the entire network
  • After an IDG disconnection, why do you get a GALLEY SHED indication on the SD?

    • ❌ It is a reminder to push the GALLEY pb to manually shed the main galley
    • ❌ It is a reminder to get the flight attendants to switch off galley equipment to decrease the load on the remaining generator
    • ✅ It is a reminder that the main galleys have been shed automatically following the loss of one generator
    • ❌ It indicates that the APU generator powers the galley equipment
  • The AC essential bus is normally supplied by:

    • ✅ The AC BUS 1
    • ❌ The AC BUS 2
    • ❌ The static inverter 1
    • ❌ The TR 2
  • The EMERGENCY GENERATOR is driven by:

    • ❌ Directly by the RAT
    • ❌ Electrically by the DC bus
    • ✅ By a hydraulic motor in the BLUE hydraulic system
    • ❌ By a hydraulic motor in the YELLOW hydraulic system
  • During an emergency electrical configuration what happens after landing?

    • ✅ Below 100 kt, DC BAT BUS is automatically connected to the batteries and below 50 kt the AC ESS BUS is no longer powered, leading to the loss of all display units
    • ❌ Below 100 kt, DC ESS BUS is automatically connected to the batteries and below 50 kt the DC ESS BUS is no longer powered, leading to the loss of all display units
    • ❌ Below 100 kt, AC ESS BUS is automatically disconnected and below 50 kt the DC ESS BUS is no longer powered from the ESS TR, leading to the loss of all display units
    • ❌ The DC BAT BUS is automatically connected to the batteries below 50 kts
  • To disconnect the IDG press the guarded IDG DISCONNECT pb-sw for:

    • ❌ At least 3 seconds
    • ✅ A maximum of 3 seconds
    • ❌ At least 10 seconds
    • ❌ A maximum of 10 seconds
  • If both the AC BUS 1 and AC BUS 2 buses are lost and the aircraft speed is above ________, the Ram Air Turbine (RAT) extends automatically:

    • ❌ 130 knots
    • ✅ 100 knots
    • ❌ 50 knots
    • ❌ 150 knots
  • Which busses will be powered after the RAT is extended and the EMER GEN begins producing electrical power?

    • ❌ DC ESS, DC ESS SHED, AC ESS and AC SHED
    • ❌ The STATIC INVERTER would power both HOT BAT busses, DC ESS and AC ESS through the AC ESS SHED busses
    • ❌ The batteries would power both HOT BAT busses, DC ESS and AC ESS through the STATIC INVERTER
    • ✅ HOT BAT busses, DC ESS, DC ESS SHED, AC ESS and AC ESS SHED