• For operating under ENGINE INTERMIX TYPE 1 condition, the following procedure applies:

    • ❌ The CM1 must progressively adjust engine thrust in 2 steps. Step 1: Idle to 70% N1 - Brakes released, when the 70% N1 is stabilized on both engines; Step 2: Both engines N1 to takeoff thrust.
    • ❌ The CM1 must progressively adjust engine thrust in 2 steps. Step 1: Idle to takeoff thrust within 5 seconds; Step 2: release brakes when takeoff thrust is stabilized on both engines.
    • ❌ The CM1 must progressively adjust engine thrust in 3 steps. Step 1: Idle to 50% N1; Step 2: release brakes and set 70% N1, when the 70% N1 is stabilized on both engines; Step 3: Both engines N1 to takeoff thrust.
    • ✅ The CM1 must progressively adjust engine thrust in 2 steps. Step 1: Idle to 50% N1 - Brakes released, when the 50% N1 is stabilized on both engines; Step 2: Both engines N1 to takeoff thrust.
  • The FADEC system is:

    • ❌ Always self powered
    • ❌ Self powered above 15% N1 and with AC power when N1 is below 15%
    • ✅ Self powered above 12% N2 and with AC power when N2 is below 12%
    • ❌ Always powered by the aircraft AC electrical circuit
  • The IDLE CONTROL of the engine has three idle modes:

    • ❌ regulated idle, ground idle, reverse idle
    • ✅ modulated idle, approach idle, reverse idle
    • ❌ bleed demand idle, regulated idle, reverse idle
    • ❌ ground idle, inflight idle, approach idle
  • Which statement is correct?

    • ❌ The ENG MASTER switch to OFF commands the closing of the LP fuel shut off valve only.
    • ❌ The FIRE HANDLE commands the closing of the LP and HP fuel shut off valves
    • ✅ The ENG MASTER switch to OFF commands the closing of the LP and HP fuel shut off valves.
    • ❌ ---
  • The thrust rating limit is computed by:

    • ❌ The FADEC according to the AP/FD mode
    • ❌ The FMGC according to the AP/FD mode
    • ✅ The FADEC according to the thrust lever position (TLA)
    • ❌ The FMGC according to the FADEC mode
  • During a manual engine start sequence:

    • ❌ Igniter A is always used
    • ❌ Igniter B is always used
    • ❌ Igniter A or B are used alternately
    • ✅ Igniters A and B are used simultaneously
  • You are about to perform a takeoff. You have not inserted a FLEX temperature. Can you still take off?

    • ✅ Yes, but only using the TO/GA detent.
    • ❌ Yes, by setting the thrust levers to the FLEX/MCT detent.
    • ❌ Not until a FLEX temperature is inserted.
    • ❌ Yes, by setting the thrust levers to the CLIMB detent.
  • The minimum starting oil temperature is:

    • ❌ - 30 °C
    • ❌ - 20°C
    • ✅ - 40 °C
    • ❌ - 50 °C
  • Which igniter channel will be used for automatic engine start?

    • ✅ Igniter A or B are used alternately
    • ❌ Igniters A and B are used simultaneously
    • ❌ Igniter A is always used
    • ❌ Igniter B is always used
  • On ground the engine start sequence is automatically aborted...

    • ❌ only in case of hot or hung start
    • ❌ There is no automatic abort sequence
    • ❌ only In case of tailpipe fire or hot start
    • ✅ in case of hot start, hung start, stall or no light up
  • During engine start sequence the gray background on N2 disappears at about 50%. What does this indicate?

    • ❌ That the start valve air pressure has dropped.
    • ✅ That the start sequence has finished and all engine parameters have stabilized.
    • ❌ That there is a start fault and a dry crank is in progress.
    • ❌ That the Igniters are no longer being powered.
  • During landing, at which speed should the reversers be set to idle latest?

    • ❌ 100 knots.
    • ✅ 70 knots
    • ❌ 50 knots
    • ❌ At taxi speed.
  • How is the FADEC electrical powered?

    • ✅ The FADEC is self-powered by a magnetic alternator above 12% N2 otherwise by A/C supply.
    • ❌ The FADEC is self-powered by an internal 28 V DC generator above 20% N2 otherwise by A/C supply.
    • ❌ The FADEC is self-powered by an internal 28 V DC generator above 12% N2 otherwise by A/C supply.
    • ❌ The FADEC is self-powered by a magnetic alternator above 20% N2 otherwise by A/C supply.
  • Manual engine start is recommended in the following cases:

    • ❌ in cold air conditions
    • ❌ when APU bleed u/s
    • ❌ for training purposes
    • ✅ after aborting a start, because of engine EGT overlimit
  • Moving the ENG MASTER switch to OFF directly commands the following: (more than one answer is correct)

    • ✅ the closing of the low pressure fuel shut off valve for the respective engine fuel system
    • ❌ the closing of the high pressure fuel shut off valve for the respective engine fuel system
    • ❌ the closing of the fuel return valve and the opening of the bypass valve
    • ❌ the closing of the fuel return valve and the closing of the bypass valve
  • What is the max TOGA time limit in dual engine case?

    • ✅ 5 minutes
    • ❌ 10 minutes
    • ❌ 15 minutes
    • ❌ no limitations
  • During the automatic start sequence of ENG 2, you notice that only igniter B is powered. Is this normal?

    • ❌ Yes, igniter A is only used for engine anti Ice
    • ❌ No, normally both igniters are used for all engine starts
    • ✅ Yes, igniters are used alternately for engine start
    • ❌ Yes, igniter B is always used for ENG 2 start
  • What is the starting EGT limit?

    • ❌ 650°C
    • ✅ 725°C
    • ❌ 850°C
    • ❌ 950°C
  • When the pilot changes from FLX to MCT by moving the thrust lever to TOGA or CL, then back to MCT, he/she cannot use the FLX rating.

    ✅ True

  • The thrust levers can only be moved manually over a sector that is divided into ___ operating segments and into___ positions defined by detents or stops

    • ❌ five, four
    • ❌ four, four
    • ✅ four, five
    • ❌ five, five
  • Which idle mode does the FADEC select in the following situation: REV are stowed after landing?

    • ❌ It switches from reverse-idle to modulated-idle, resulting in an increase of thrust
    • ❌ It switches from reverse-idle to ground-idle, resulting in a decrease of thrust
    • ❌ It switches from reverse-idle to ground-idle, resulting in an increase of thrust
    • ✅ It switches from reverse-idle to modulated-idle, resulting in a decrease of thrust
  • Manual engine starting is recommended after aborting a start because of:

    • ❌ Engine stall
    • ❌ Engine EGT overlimit
    • ❌ Low start air pressure
    • ✅ All answers are correct
  • Starter limitations:

    • ✅ no running engagement of the starter , when N2 is above 20%
    • ❌ pause between start attempts: 25 s
    • ❌ cooling period, after 4 start attempts: 20 min
    • ❌ 4 consecutive cycles: each lasts a maximum of 3 min
  • The maximum permissible N1 is the red arc, showing the prohibited or 'redline' area of operation. It begins at _________.

    • ❌ 101%
    • ❌ 102%
    • ❌ 103%
    • ✅ 104%
  • During a manual start, what function does the FADEC perform?

    • ❌ Active controlling of the engine and monitoring the start valve, the HP fuel valve and the ignition
    • ✅ Passive monitoring of the engine and active control of start valve, HP fuel valve and ignition
    • ❌ Active control of the entire start sequence and take corrective action only in case of major failures or malfunctions
    • ❌ It does not perform any function during a manual start and all actions have to be carried out by the pilots (FADEC only on standby)
  • Which component opens the start valve during manual start?

    • ❌ Directly via manual start valve only
    • ✅ Automatic via the FADEC after ENG MAN START pb has been pushed
    • ❌ Directly via the ENG MAN START pb
    • ❌ Manual directly via the ENG MODE selector
  • Moving the ENG MASTER switch to OFF directly commands the closing of :

    • ❌ Both the LP and HP fuel shut off valves and the hydraulic shut off valve
    • ✅ Both the LP and HP fuel shut off valves
    • ❌ The LP fuel shut off valve
    • ❌ The HP fuel shut off valve
  • Take off should be performed using which power settings?

    • ❌ Any manual setting.
    • ❌ CLIMB and TO/GA.
    • ❌ FLEX and MCT.
    • ✅ FLEX/MCT and TO/GA.
  • The REV green indication on the E/WD N1 indication appears when:

    • ❌ The minimum 2 of the 4 blocker doors of the associated engine are fully deployed
    • ❌ All 4 blocker doors of the associated engine are unlocked and a minimum of 2 blocker doors are fully deployed
    • ❌ The thrust levers are selected to either full or idle reverse detent
    • ✅ All 4 blocker doors of the associated engine are fully deployed
  • The Thrust Reverser Auto Restow Function …

    • ❌ is inhibited on ground only.
    • ❌ stows thrust reverser doors if N1 greater than 70%.
    • ❌ restows the thrust reverser doors in case of hydraulic failures.
    • ✅ is inhibited in flight and on ground, with N1 greater than 70%.
  • Engine cranking may be manually selected by setting:

    • ❌ With master switch in OFF position the mode selector to NORM and the MAN START pb to on
    • ✅ With master switch in OFF position the mode selector to CRANK and the MAN START pb to on
    • ❌ With master switch in ON position the mode selector to CRANK and the MAN START pb to on
    • ❌ The mode selector to CRANK and the master switch to ON
  • When are both igniters powered during engine start sequence?

    • ✅ If the automatic start fails, the FADEC energizes both igniters at the same time during the second engine start attempt.
    • ❌ The FADEC is testing both igniters before selecting the one to be used.
    • ❌ Both igniters are always used for every engine start.
    • ❌ Engine anti-ice has been selected on prior to engine start.
  • Which idle mode does the FADEC select in the following situation: Inflight in descent through FL250?

    • ❌ Reverse idle
    • ✅ Modulated idle
    • ❌ Approach idle
    • ❌ Hard idle
  • You press the A/THR DISCONNNECT BUTTON at the thrust lever longer than 15 seconds. What will happen?

    • ❌ A/THR will not be disconnected until the engines are running
    • ❌ A/THR will be disconnected for the remainder of the flight if the engines are started within the next 30min only (Thereafter it must be disconnected again)
    • ✅ A/THR will be disconnected for the remainder of the flight. All A/THR functions are lost, and they can be recovered only at the next FMGC power-up (on ground)
    • ❌ A/THR will not be disconnected
  • In manual start, the thrust lever position must be set to idle, otherwise

    • ❌ The engine will not start
    • ✅ The engine will rapidly accelerate to generate the thrust demanded by the TLA
    • ❌ The engine will be stuck TOGA position
    • ❌ There will be no effect. The engine will run at idle after start until the thrust lever will be moved
  • Which statement is correct?

    • ❌ The FADEC doesn’t prevent the thrust from exceeding any limit.
    • ❌ The FADEC prevents the thrust from exceeding the limit for the thrust lever position in manual mode only.
    • ✅ The FADEC prevents the thrust from exceeding the limit for the thrust lever position in both manual and automatic modes.
    • ❌ The FADEC prevents the thrust from exceeding the limit for the thrust lever position in automatic mode only.
  • What happens if you select reverse inflight?

    • ❌ Nothing happens
    • ✅ You get an ECAM caution ENG REV SET
    • ❌ The reversers will be deployed and thrust according TLA will be set
    • ❌ The reverser doors are unlocked and the FADEC selects reverse idle thrust
  • The following functions are provided by the FADEC during a manual engine start:

    • ✅ Opening of the start valve when the ENG MODE selector is set to IGN/START and the MAN START pushbutton switch is pressed. The FADEC makes a passive survey of the engine during the starting sequence.
    • ❌ Positioning of the HP fuel valve and operation of both igniters when the engine master switch is turned on. The FADEC has full authority over the start sequence.
    • ❌ For an inflight start, the FADEC decides whether the engine is windmilling fast enough or needs assistance from the starter in view of current engine parameters and flight environment.
    • ❌ During a manual start, the FADEC never has the authority to abort the start sequence.
  • The minimum oil temperature for takeoff is:

    • ❌ - 15 °C
    • ❌ +10 °C
    • ✅ - 10 °C
    • ❌ 0 °C
  • In manual mode, when the thrust levers are between the climb detent and idle:

    • ❌ N1 is frozen
    • ❌ N1 is climb N1
    • ❌ N1 is idle N1
    • ✅ Each position of the thrust levers corresponds to an N1