• With the APU running, the APU BLEED pb pushed and the X-BLEED selector to AUTO, the APU will:

    • ❌ Only supply bleed air to the right side
    • ❌ Supply bleed air only to the left side unless the X-Bleed selector is set OPEN
    • ✅ Supply pneumatic air to both sides of the aircraft because the pneumatic crossbleed valve automatically opens
    • ❌ Only supply bleed air to the left side
  • The following symbols are displayed on the ECAM BLEED system page:

    • ✅ The IP and HP ports, the engine bleed valves, the precoolers air inlet pressure and outlet temperature values, the APU BLEED valve when the APU is running
    • ❌ The IPVs, the high pressure ground indication, always displayed on ground even if the ground unit is not connected
    • ❌ The OPVs, the crossbleed valve, the pack valves
    • ❌ The non return valves, the APU bleed valve, the pack compressor outlet temperature
  • The pneumatic system supplies high-pressure air for:

    • ✅ Air conditioning, engine starting, wing anti-icing, water pressurization and hydraulic reservoir pressurization
    • ❌ Only for engine starting and Wing anti-icing
    • ❌ Only for air conditioning and Water pressurization
    • ❌ Only for engine starting, wing anti-icing and hydraulic reservoir pressurization
  • How many sources does high pressure air have?

    • ❌ One ( engine bleed system )
    • ✅ Three (engine bleed system & APU load compressor & HP ground connection)
    • ❌ Two ( engine bleed system & APU load compressor )
    • ❌ Four (engine bleed system & APU load compressor & HP ground connection & LP ground connection )
  • What are the possible selections of the crossbleed valve selector on the overhead AIR COND panel?

    • ❌ ON, OFF
    • ❌ AUTO, X-FEED, CLOSE
    • ❌ OPEN, CLOSE
    • ✅ SHUT, AUTO, OPEN
  • When selected, APU bleed air:

    • ❌ Will supply bleed air only if the ENG BLEED pb’s are manually selected OFF
    • ❌ Will supply bleed air only if the X-BLEED selector is selected OPEN
    • ✅ Has priority over engine bleed air
    • ❌ Does not have priority over eng bleed air
  • How does the precooler operate and what is its purpose?

    • ✅ It uses cooling air bled from the engine fan to regulate the temperature according to the demand before the bleed air is distributed to the users
    • ❌ It uses air extracted from the cooling air inlet (CFM) to regulate the temperature as calculated by the ACSCs
    • ❌ It uses air extracted from the cooling air inlet (CFM) to regulate the temperature as calculated by the AEVCs
    • ❌ It senses the temperature downstream of the HPV and opens or closes the IPV accordingly to regulate the temperature of the bleed air before it is distributed to the users
  • In order to use bleed from the APU in flight, the aircraft has to be at or below:

    • ❌ FL200
    • ✅ FL225
    • ❌ FL250
    • ❌ FL300
  • Following an ENGINE1 BLEED FAULT why can you only use one pack if Wing Anti Ice is on?

    • ❌ Only one user can be supplied via the X BLEED duct.
    • ❌ If you use wing A/I, the X BLEED valve is automatically closed. Therefore, pack 1 will no longer be supplied.
    • ✅ One ENG BLEED system cannot supply 2 packs and wing A/I.
    • ❌ ---
  • Engine-Bleed valve opens if:

    • Upstream pressure is above 8 psi

    • APU bleed pushbutton switch is off or APU bleed valve is closed.

    • There is no onside wing or pylon leak, and no overpressure or overtemperature has been detected.

    • The ENG FIRE pushbutton has not been popped out and the engine start valve is closed

    ✅ True

  • What is the purpose of the crossbleed valve?

    • ❌ It enables both the left and right bleed systems to equalize the air pressure in the ducts before the bleed air is distributed to the users
    • ❌ Its sole purpose is to permit a crossbleed engine start and to isolate both bleed systems in case of smoke
    • ❌ It permits the interconnection or isolation of both bleed systems upstream of the bleed valves and OPVs
    • ✅ It permits the interconnection or isolation of both bleed systems downstream of the precoolers
  • The APU BLEED pb FAULT light illuminates amber if:

    • ❌ Overheat is detected
    • ❌ A malfunction and an overheat are detected
    • ✅ An APU bleed leak is detected
    • ❌ A malfunction is detected
  • Which system controls and monitors the operation of the pneumatic system?

    • ❌ The Flight Warning Computer FWC
    • ✅ Two Bleed Monitoring Computers BMC1 and BMC2
    • ❌ One Bleed Control Computer BCC
    • ❌ Two Cabin Pressurization Computers CPC1 and CPC 2
  • With engines and APU running and APU bleed valve selected on. Select the correct statement:

    • ✅ Engine bleed valves close, X-Bleed valve opens, APU bleed valve opens.
    • ❌ Engine bleed valves open, X-Bleed valve closes, APU bleed valve opens.
    • ❌ Engine bleed valves close, X-Bleed valve closes, APU bleed valve opens.
    • ❌ Engine bleed valves open, X-Bleed valve opens, APU bleed valve closes.
  • How is the Crossbleed Valve controlled?

    • ❌ Pneumatically
    • ❌ Hydraulically
    • ✅ Electrically
    • ❌ All answers are correct
  • Each bleed valve is normally:

    • ❌ Electrically operated and pneumatically controlled by the opposite BMC
    • ✅ Pneumatically operated and electrically controlled by its associated BMC
    • ❌ Pneumatically operated and electrically controlled by the opposite BMC
    • ❌ Electrically operated and pneumatically controlled by its associated BMC
  • The following is true about the bleed supply source:

    • ❌ An intermediate pressure valve can cut off bleed air from the HP port
    • ❌ A non return valve at the HP port protects the compressor against a reverse flow from the IP port
    • ✅ A non return valve at the IP port protects the compressor against a reverse flow from the HP port
    • ❌ A check valve can cut off bleed air from the compressor air extract port
  • Bleed leak detection system: For the pylon and APU, the sensing elements are tied to form a ____________loop and for the wing a _______________loop.

    • ❌ double / single
    • ❌ single / single
    • ❌ double / double
    • ✅ single / double
  • Temperature regulation of the bleed air is achieved by the precooler which regulates the temperature to:

    • ❌ 85°
    • ❌ 60°
    • ❌ 150°
    • ✅ 200°
  • During normal operation, what happens in the pneumatic system as the engine power is increased for take off?

    • ✅ The pressure delivered from the IP stages is sufficient and the HP valves are automatically closed
    • ❌ The HP valves open fully to permit sufficient bleed supply in case of pack failure
    • ❌ The crossbleed valve closes if APU is being used
    • ❌ The precooler fan valve is turned off until lift off
  • Engine bleed indications on the precooler inlet pressure are normally green. The light becomes amber if under _________ or if overpressure detected by the BMC:

    • ❌ 3 psi
    • ❌ 6 psi
    • ✅ 4 psi
    • ❌ 2 psi
  • The bleed valve function is to act as:

    • ✅ A shut off and pressure regulating valve
    • ❌ A reverse flow protection valve when the APU is not running
    • ❌ A temperature and pressure regulating valve
    • ❌ A temperature regulating valve
  • A FAULT light in the ENG 2 BLEED pb indicates, among others:

    • ❌ The ENG FIRE pushbutton has not been popped out
    • ❌ There is an under pressure upstream of the bleed valve
    • ✅ The bleed valve is not closed with APU bleed ON
    • ❌ The engine anti-icing is not receiving enough bleed air in idle conditions
  • The ENG BLEED LEAK caution comes ON at:

    • ❌ A temperature of > 165°
    • ✅ A temperature of > 204°
    • ❌ A temperature of > 185°
    • ❌ A temperature of > 234°
  • Air is normally bled from the:

    • ✅ IP stage, at low engine speed from the HP stage
    • ❌ HP stage, at low engine speed from the LP stage
    • ❌ LP stage, at low engine speed from the IP stage
    • ❌ HP stage, at low engine speed from the IP stage
  • A leak detection system in the pneumatic circuit detects any overheating in the vicinity of:

    • ✅ The hot air ducts
    • ❌ The engine anti-icing piccolo tubes
    • ❌ The precooler downstream of the bleed valve
    • ❌ The hot air valves
  • Preparing the aircraft for de-icing, the before spraying fluid checklist demands:

    • ❌ Switch ENG 1 + 2 Bleed pb off
    • ❌ Switch ENG 1 + 2 Bleed and APU Bleed pb on
    • ✅ Switch ENG 1 + 2 Bleed pb and APU Bleed pb off
    • ❌ Switch ENG 1 + 2 Bleed pb on
  • How many pneumatic safety valves prevent cabin pressure from exceeding limits?

    • ❌ One
    • ✅ Two
    • ❌ Three
    • ❌ Four
  • With the loss of pneumatic system pressure, the engine bleed valve will:

    • ❌ Remain in its current position
    • ❌ Move to the mid position
    • ✅ Move to the closed position
    • ❌ Move to the open position
  • APU bleed may be used, if the APU speed is above:

    • ❌ 50 %
    • ❌ 100 %
    • ✅ 95 %
    • ❌ 80 %
  • The aircraft has two similar engine bleed air systems. Each system is designed to:

    • ❌ Select the compressor stage to use as a source of air
    • ❌ Regulate the bleed air temperature
    • ❌ Regulate the bleed air pressure
    • ✅ All answers are correct
  • If one BMC fails, the adjacent BMC takes over the monitoring of the bleed system to issue the following ECAM warnings if necessary:

    • ❌ Overpressure
    • ❌ Wing leak
    • ❌ Overtemperature
    • ✅ All answers are correct
  • A leak in the bleed system is detected by:

    • ❌ Overpressure detection loops
    • ✅ Overheating detection loops
    • ❌ Smoke detection loops
    • ❌ Overspeed detection loops
  • APU Bleed pb sw ON: The APU valve opens if N > ___ % and there is no leak in the APU or in the left side bleed

    • ✅ 95%
    • ❌ 80%
    • ❌ 85%
    • ❌ 90%
  • PNEU - Engine Bleed System - Temperature Regulation and Limitation: Air bleed from the engines is:

    • ❌ Not cooled.
    • ✅ Cooled in a heat exchanger by cooling air bleed from fan section.
    • ❌ Cooled in a heat exchanger by ambient air.
    • ❌ ---