• Will the floor proximity marking system batteries be charged when the EMER EXIT LT switch is set to AUTO?

    • ✅ No, because it is a self-luminescent marking system
    • ❌ Yes, but only in flight
    • ❌ Yes, but only on ground
    • ❌ No, it has integrated batteries, which will be charged as long as external power is connected to the aircraft or the engine generators are supplying the network (regardless of the switch position)
  • All instruments and panels have integrated lighting in the cockpit (other than display units). The brightness of all integral lighting is.

    • ✅ Adjustable
    • ❌ Fixed.
    • ❌ Automatic
    • ❌ ---
  • How are the emergency lights supplied during an emergency evacuation?

    • ❌ By DC ESS BUS
    • ❌ By HOT BAT BU
    • ❌ By DC ESS SHED BUS
    • ✅ By the internal batteries
  • Where are the beacon lights located?

    • ✅ One on top of the fuselage and one below the fuselage
    • ❌ One on each wing tip
    • ❌ One on the landing gear and one on the vertical stabilizer
    • ❌ ---
  • Which cockpit light(s) is (are) supplied by DC GND/FLT bus?

    • ❌ Both dome lights
    • ❌ Only the right dome light
    • ✅ Only the left dome light
    • ❌ Both dome lights, but only in DIM position
  • This switch sets the brightness of all the cockpit annunciator lights at either bright or dim, and also tests them. TEST : Illuminates all flight deck annunciator lights. Puts 8's up in all liquid crystal displays (LCDs). DIM : Reduces voltage to all annunciator lights. BRT : Allows annunciators to function normally. Note : Transfer of data between ECAM and the ND and switching between the electronic instrument system and the display management computer are not allowed during the ANN LT test.

    ✅ True

  • Each of the CONSOLE/FLOOR switches controls the lights for the side console and briefcase on one side of the cockpit, and for the floor around one of the pilot's seats. The lights can either be:

    • ❌ HI, MED, LO, or OFF
    • ❌ ) HI, LO, or OFF
    • ✅ BRIGHT, DIM, or OFF
    • ❌ BRIGHT, DIM1, DIM2, or OFF
  • The STROBE light selector is set to AUTO. In this position, when do the strobe lights stop flashing?

    • ✅ When the aircraft touches down
    • ❌ When the first reverser is deployed
    • ❌ When the landing lights are switched off
    • ❌ When the last engine has been shut down
  • The Strobe Light is OFF, which indication do you have latest after lift-off/inflight?

    • ❌ No indicatio
    • ✅ Memo Display: STROBE LT OFF in green
    • ❌ Single Chime after T/O inhibition
    • ❌ Advisory in scratchpad
  • If the LIGHT EMER pb on the purser’s panel is pushed to ON,

    • ❌ the emergency lighting is turned on only if EMER EXIT LT selector is on ARM.
    • ❌ the emergency lighting is turned on only if EMER EXIT LT selector is on ARM and ON.
    • ✅ the emergency lighting is turned on also if EMER EXIT LT selector is on OFF.
    • ❌ the EMER EXIT light in the cockpit comes ON
  • Each of the CONSOLE/FLOOR switches controls the lights for the side console and briefcase on one side of the cockpit, and for the floor around one of the pilot's seats. The lights can either be:

    • ❌ HI, MED, LO, or OFF
    • ❌ HI, LO, or OFF
    • ✅ Bright, Dim, or Off
    • ❌ ---
  • The INTEG LT MAIN PNL and PED knob adjusts the brightness of integral lighting for the main panel and pedestal, and turns it on and off.

    ✅ True

  • What is the only lighting source in the EMER ELEC configuration?

    • ✅ L main INST panel, R DOME light and STBY compass/ice indicator
    • ❌ R main INST panel, L DOME light and STBY compass/ice indicator
    • ❌ Both Dome lights
    • ❌ R DOME light and L main INST panel light only
  • Which parts of the exterior lighting are controlled by switches on the overhead panel?

    • ❌ Navigation lights, landing lights.
    • ❌ Runway turn off lights, to and taxi lights, logo lights.
    • ❌ Anticollision lights, wing and engine scan lights.
    • ✅ all named lights are controlled by the switches
  • This switch turns on and off the three synchronized strobe lights, one on each wing tip and one below the tail cone. ON : The strobe lights flash white. AUTO : The strobe lights come on automatically when the main gear strut is not compressed. OFF : The strobe light are off.

    ✅ True

  • The STROBE light selector is set to AUTO. In this position, when do the strobe lights stop flashing?

    • ✅ When the aircraft touches down
    • ❌ When the first reverser is deployed.
    • ❌ When the landing lights are switched off.
    • ❌ When the last engine has been shut down.
  • With EMERG EXIT LT switch in position ARM the EXIT SIGNS automatically come on:

    • ✅ When normal aircraft electrical power system fails
    • ❌ After Engine shut down and all slides disarmed
    • ❌ After Engine shut down and at least one slide deployed
    • ❌ During Emergency Descent as soon as the descent is initiated
  • The floor proximity emergency escape path marking is:

    • ❌ Powered by the hot BAT bus number one
    • ❌ Powered by the DC essential bus
    • ❌ Powered by the AC essential bus
    • ✅ A self-luminescent system
  • The LOGO lights are illuminated

    • ❌ When the aircraft altitude is below 10.000 feet measured by ADIRU number 1 and the flaps are set to position 1
    • ❌ At all times if the LOGO light switch is set to ON and on the ground only and if the LOGO light switch is set to AUTO
    • ✅ NAV and Logo sw to 1 or 2 and when the main gear struts are compressed or the flaps are extended at least at 15 degrees
    • ❌ With NAV and Logo sw to 1 or 2, On Ground all the times and inflight as long as the Landing Lights are extended additionally
  • The RWY Turnoff Lights:

    • ✅ Are located at the nosewheel gear
    • ❌ ) Are installed below each wing
    • ❌ Switched off automatically upon liftoff
    • ❌ Remain on during the flight